ISO/TS TECHNICAL SPECIFICATION 13399-309 First edition 2016-03-01 Cutting tool data representation and exchange - Part 309: Creation and exchange of 3D models - Tool holders for indexable inserts Repreésentation et échange des données relatives aux outils coupants Partie 309: Création et échange de modeles 3D - Porte outil a plaquette amovible Reference number IS0/TS 13399-309:2016(E) ISO International Organization for Standardization @ IS0 2016 IHS unde ed without license from IHS IS0/TS 13399-309:2016(E) COPYRIGHTPROTECTEDDOCUMENT IS0 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. IsOcopyrightoffice Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org Internationai ir PrganizationforStandardization ensee-ZHEJIANG INST.OF STANDARDIzARoISQ16- All rights reserved networking permitted without license from IHS IS0/TS 13399-309:2016(E) Contents Page Foreword ..vi Introduction. ..vili 1 Scope. 2 Normative references 3 Starting elements, coordinate systems, planes 2 3.1 General. .2 3.2 Reference system (PCS primary coordinate system) .2 3.3 Tool item position. 2 3.3.1 Prismatic tool position ..3 3.3.2 Round tool position.. .3 3.4 Planes .4 3.5 Cutting reference point (CRP) .5 3.6 Design of the pocket seat .8 3.7 Adjustment coordinate system on workpiece side .12 3.7.1 General ..12 3.7.2 Designation of the coordinate system workpiece side ..12 4 Design of the model .14 4.1 Necessary parameters for the connection interface feature ..14 4.2 Necessary properties for insert and pocket seat.. ..15 4.2.1 General. ..15 4.2.2 Properties for equilateral, equiangular and equilateral, non- equiangular inserts.. .15 4.2.3 Properties for non-equilateral, equiangular and non-equilateral, non- equiangular inserts. ..15 4.2.4 Properties for round inserts ..16 4.2.5 Design of the pocket seat feature ..16 5 Tool holder for longitudinal and transversal turning .17 5.1 General. .17 5.2 Necessary properties 17 5.3 Basic geometry .18 5.4 Turning tool with pocket seat and top surface offset 21 5.5 Turning tool assembly 21 5.6 Boring bar body. .22 6 Turning tool for external threading .24 6.1 General. .24 6.2 Necessary properties. 24 6.3 Basic geometry. .25 6.4 Turning tool with pocket seat and top surface offset .25 6.5 Turning tool assembly 26 7 Boring bar for internal threading .27 7.1 General 27 7.2 Necessary properties 27 7.3 Basic geometry 28 7.4 Boring bar with pocket seat and top surface offset 29 7.5 Boring bar assembly. 30 8 Turning tool for OD grooving and parting .30 8.1 General... 30 8.2 Necessary properties. 30 8.3 Basic geometry. 32 8.4 Grooving tool with pocket seat and top surface offset .33 8.5 Grooving and cut-off tool assembly .33 iii ISee=ZHEJIANG INST OF STANDARDIZATION C1 5956617 vided by IHS under license with ISO vithoutlicense from IHS Not for Resale, 2016/4/26 02:46:53