ISO INTERNATIONAL STANDARD 16368 Second edition 2010-05-15 Mobile elevating work platforms - Design, calculations, safety requirements and test methods Plates-formes élévatrices mobiles de personnel- Conception, calculs, exigences de sécurité et meéthodes d'essai Reference number ISO 16368:2010(E) @ ISO 2010 py IHS under lic itted without license from IHS Not for Resale ISO 16368:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below COPYRIGHTPROTECTEDDOCUMENT @ISO2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, isO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ Iso 2010 - All rights reserved I without license from IHS Not for Resale ISO 16368:2010(E) Contents Page Foreword Introductior 1 Scope 2 Normative references.. 3 Terms and definitions. 4 Safety requirements and/or protective measures 10 4.1 Compliance.. 10 4.2 Structural and stability calculations. 10 4.3 Chassisandstabilizers.. 21 4.4 Extending structure.. 27 4.5 Extending structure drive systems 4.6 Work platform........ 4.7 Controls... 41 4.8 Electrical equipment . 43 4.9 Hydraulic systems 4.10 Hydraulic cylinders 45 4.11 Safety devices.. .50 5 Verification of the safety requirements and/or measures. 52 5.1 Examinations and tests 52 5.2 Type tests... 62 5.3 6 Information for use 6.1 General .63 6.2 Instruction handbook.. .63 6.3 Marking...... Annex A (informative) Use of MEwPs in wind speeds greater than 12,5 m/s - Beaufort Scale 6....67 AnnexB(informative)Dynamicfactorsinstabilityandstructuralcalculations.. AnnexC(normative)Calculationofwire-ropedrivesystems ..69 Annex D (informative) Calculation example Wire-rope drive systems 76 Annex E (informative) Kerb test calculations... AnnexF(informative)Instructionhandbook Annex G (normative) Additional requirements for cableless controls and control systems ... ...88 Annex H (informative) List of significant hazards 06 Bibliography.... .94 CopyrghtInternational OrganizaionSadardizaoghtsreserved ii nse from IHS Not for Resale ISO 16368:2010(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has been International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 16368 was prepared by Technical Committee ISO/TC 214, Elevating work platforms This second edition ca